Real Central Skylights project · Rye, VIC
Skylight Installation in Rye: Two VELUX FS C08 Fixed Skylights
This completed Rye project added two aligned fixed skylights above a large living area. The shallow-pitch corrugated metal roof required raised custom Colorbond flashings and backflashing, while the high ceiling cavity was finished with two individual plaster shafts.
- Job #48971
- Supply & install
- 2 × VELUX FS C08
- Low-pitch metal roof
- Custom raised flashing
Project overview
A paired skylight layout for a large Rye living area
The two long fixed skylights were positioned in parallel through the central ceiling zone. The work combined product supply, roof openings, custom metal-roof flashing, backflashing, installation, internal framing and plaster shaft construction.
Finishing note: the installation photos show the plaster shafts before final decorating. Painting was left to the client.
Planning to completed result
Before and after the Rye skylight installation
The planning photo records the intended positions over the living area. The completed view was taken from a different side of the room and shows both skylights and their plaster shafts in place.
Product and roof detail
VELUX FS C08 skylights on a shallow-pitch metal roof
The job used two VELUX FS C08 fixed skylights, each measuring 550 × 1400 mm. A site pitch record showed approximately 6.5 degrees, and the project paperwork specified that the custom flashings were to be inclined or raised to between 5 and 10 degrees.
The completed roof photographs show each skylight integrated into a broad custom metal tray, with extended backflashing running upslope. The custom flashing colour was listed as Shale Grey Colorbond.
For homeowners comparing fixed skylights, see the VELUX FS fixed skylight range. Roof suitability and flashing requirements still need to be assessed for each property.
Installation approach
How this Rye project progressed
The photographs record the project from initial layout through roof preparation, custom flashing and internal shaft work. The sequence below reflects the visible stages rather than a minute-by-minute work schedule.
Measure and position
The intended ceiling and roof positions were marked, and the shallow roof pitch was recorded.
Create and frame openings
Two aligned openings were formed through the corrugated roof and prepared around the roof structure.
Install and weatherproof
The two VELUX units were fitted with raised custom flashings and extended Colorbond backflashing.
Build the light shafts
Separate internal shafts were framed and plastered through the high cavity, ready for later decoration.
Project photo story
Roof preparation, custom flashing and completed interior
These selected photographs show the useful stages of the job without repeating near-identical views.
Completed outcome
A balanced pair of fixed skylights across the main ceiling zone
The finished photographs show two long skylight openings arranged evenly across the room. Each unit has its own rectangular shaft, allowing daylight to enter at two points rather than through one oversized central opening.
The project is also a useful example of why a metal-roof skylight installation is more than cutting an opening and placing a window. On this property, the custom raised trays, extended backflashing and high internal cavity were central parts of the installation scope.
Helpful next steps
Products and services related to this Rye project
Mornington Peninsula
Skylight installation around Rye and nearby areas
This completed skylight installation in Rye demonstrates the roof and internal work that may be required for a shallow-pitch metal-roof home. Nearby areas commonly assessed include:
- Tootgarook
- Rosebud
- Blairgowrie
- Sorrento
- Dromana
- Safety Beach
- Mornington
Project-specific questions
FAQ: skylight installation in Rye
What skylights were installed on this Rye project?
Two VELUX FS C08 fixed skylights were supplied and installed. Each skylight measured 550 × 1400 mm.
Why were custom flashings used?
The photographs show a corrugated metal roof, and the site record showed a shallow pitch of approximately 6.5 degrees. The project therefore specified raised custom Colorbond flashings, together with extended backflashing.
Was the internal ceiling work included?
Yes. The project included framing and plaster shaft work for both skylights, with internal scaffold used for the high cavity. Final painting was left to the client.
Were these opening or electric skylights?
No. The installed VELUX FS units are fixed skylights. No opening, solar or electrical operation was included in this project.
Can Central Skylights quote a similar project in Rye?
Yes. Send clear roof and ceiling photos through the online quote form, or book a free measure and quote appointment so the roof, cavity and flashing requirements can be assessed.
Planning a skylight installation in Rye?
Share photos of the room, ceiling and roof. We can help identify a suitable VELUX model and the flashing and shaft work your property may require.